DEBURR & GAUGE TOOL

  • bvseo_sdk, p_sdk, 2.3.0.1
  • CLOUD, method:getAggregateRating, 36.31ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Information

The SharkBite Large Diameter Deburr and Gauge Tool is designed for use with Copper, PEX, CPVC, PE-RT and HDPE pipe. This tool also accurately measures insertion depth for SharkBite push-to-connect fittings (1-1/4” up to 2”) as well as deburring with a simple rotation of the tool once the pipe is inserted.

SizesPart #
1-1/4", 1-1/2", 2" Deburring & Depth Gauge Tool
UXLG03

Reviews

  • bvseo_sdk, p_sdk, 2.3.0.1
  • CLOUD, method:getReviews, 8.15ms
  • REVIEWS, PRODUCT
  • bvseo-msg: HTTP status code of 404 was returned;

Questions

Do you have to use this tool to install the sharkbites?

Asked by: Tina B
Hello, The SharkBIte deburr & depth gauge tool (part # UXLG03) is designed to measure pipe insertion depth and deburr copper pipe when using our large diameter (1-1/4", 1-1/2", and 2") push-to-connect fittings that have part numbers starting with "UXL". This tool is not necessary if you have a tape measure to measure the pipe's insertion depth and an external deburring tool to remove any burrs or sharp edges from the copper pipe. The insertion depths for our UXL line of large diameter fittings are below. If you have additional questions please feel free to contact our customer service department at 877-700-4242. • 1-¼” fitting – 1.8” • 1-½” fitting – 2.0” • 2” fitting – 2.1” Regards
Answered by: SharkBite118
Date published: 2018-11-26

does item numberuxlg03 work for half inch plumbing?

Asked by: steven p
Hello, Part # UXLG03 is only suitable for 1-1/4", 1-1/2" and 2" pipe. Part # U702 is suitable for 1/4" - 1" pipe. Please see the link below. http://www.sharkbite.com/product/deburr-gauge-tool/ Thank you
Answered by: SharkBite118
Date published: 2018-07-27

I do not have a depth gauge. How deep should 1/2" copper and 1/2" CPVC go into the 1/2" coupling?

Asked by: Mike D
Hello, Our 1/2" fittings have an insertion depth of 15/16". Thank you
Answered by: SharkBite118
Date published: 2018-12-11

Do I need a debuting tool for 1/2 inch?

Asked by: Cmtcat
You do not necessarily need the deburring tool, but if you are using copper, you need to make sure the copper is properly deburred before putting a SharkBite fitting on. Using sandpaper is OK as well, but you just need to make sure the outer edge of the copper is smooth so nothing can cut the rubber O-ring inside of the fitting.
Answered by: sharkbite_rm
Date published: 2018-11-26
  • y_2018, m_12, d_16, h_24CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.9
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_US, sid_700, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_sharkbite
  • bvseo_sdk, p_sdk, 2.3.0.1
  • CLOUD, method:getContent, 69.28ms
  • QUESTIONS, PRODUCT

Related Products

Find a Store
Add to Project List
  Clear selection